There are numerous components that must cooperate with one another in order for your car to function properly. The tensioner pulley is one of these modest but crucial components. A tensioner pulley applies the necessary pressure and aids in maintaining the belt’s tension and alignment using a spring-loaded arm or a hydraulic actuator.
The tensioner pulley on a drive belt system is spring-loaded to maintain the serpentine belt’s appropriate tension and alignment. Well, in this article we’ll be discussing the symptoms of a bad tensioner pulley.
Let’s Begin!
Learn about Timing Belt with this detailed guide!
What is Tensioner Pulley and How it work?
A tensioner pulley is a crucial component in a vehicle’s timing system, responsible for achieving precise transmission and constant belt tension. It increases the angle embraced in belt drives, gives tension to the belt, transfers the driving force of the crankshaft, compensates for elongation of the strap, allows for shorter wheelbases, and prevents belt slippage.
There are various types of tensioner pulleys, including fixed and automatic types, which can compensate for changes in temperature or belt load. The pulley’s rolling surface can be smooth or profiled, and its basic components include a rigid radial bearing, inner and outer ring, retainer, grease, and seal.
Understanding the alternator pulley function can provide insight into the various roles pulleys play in the vehicle’s engine system, ensuring optimal performance.
You should also learn about Timing Chain with this detailed guide!
Tensioner Pulley Location
The tensioner’s spring-loaded tensioner pulley is located at the end of the tensioner. The spring-loaded component of the arrangement applies tension to the auxiliary belt as it travels across the pulley. To prevent it from slipping off the pulleys, it needs to be under the proper amount of strain.
Sometimes the component that breaks down isn’t the tensioner. Sometimes the failure of the bearing results in the pulley. Because of this, you can buy a pulley as a replacement rather than a tensioner. In a moment, I’ll talk more about that.
You can use the procedures below to locate the tensioner pulley.
- Open the hood of the car.
- To locate the tensioner, search the length of the auxiliary drive belt. The pulley, which is attached to the tensioner, has a flat surface toward the top of the belt. There won’t be any grooves where the belt rides.
Consult the manufacturer’s manual of your car if you can’t seem to locate the tensioner pulley. If not, you could require assistance from a nearby dealership or mechanic.
Functions
A belt tensioner is a small component with four main parts: a base, tensioner arm, spring, and pulley. It is a metal part that holds all other parts and applies pressure to the serpentine belt, allowing enough slack for adjustments or removal. The spring provides pressure to keep the tensioner tight, and the pulley is a rotating part that allows the belt to move.
All belt tensioners have a similar design, with some being larger and others smaller. They are always on the serpentine belt’s path, with a smaller pulley. The belt tensioner is important because it keeps the serpentine belt tight enough to power accessories like the AC compressor, alternator, and power steering. In a Mazda CX7 engine, the belt tensioner is located on the right side.
You should learn about Water Pump with this detailed guide!
Symptoms Of A Bad Tensioner Pulley
Weird noises
The noise is typically the first thing to be noted when the tensioner pulley begins to malfunction. The belts will start to squeak or chirp as the tensioner becomes looser. When you first turn on the engine, you might detect this sound the loudest. It becomes very irritating and is the most common grievance among car owners. It is common for the noise to change as the bearing or pulley totally wears out. Even more concerning is the possibility that the pulley will now begin to grind.
Burnt odor
The serpentine belt will loosen and start to slide on the accessory pulleys if the tensioner pulley is damaged and unable to tension the belt appropriately. While driving, this may cause your automobile to smell like burned rubber. You should inspect the belt and tensioner pulley as soon as you can if you smell burnt material.
Excessive Belt Wear
You can begin to have issues with the belt itself if the drive belt tensioner or pulley starts to malfunction. The belt may show signs of severe or unusual wear. There may be problems with the pulley if the tensioner fails. The belt edges may begin to fray as a result. In the worst-case scenario, you can end up with a broken belt, which is never nice. The pulley should be changed ideally before things deteriorate to this point.
You should learn about Flat Belt Pulley with this detailed guide!
Failing Accessories
The belt, which operates a variety of accessories like the alternator, water pump, and air conditioner compressor in most cars, is held in place by the tensioner and pulley. Power to these components is lost if the belt breaks or gets slack. You’ll lose access to these items, and odd problems can start to appear. The engine could overheat, the alternator could stop charging, and the air conditioning could cease working.
You’ll pay more for repairs if a poor pulley or tensioner causes a broken belt. You’ll need to replace the belt and other damaged components in addition to the pulley.
Here are other symptoms
- The pulley is being rocked back and forth. There shouldn’t be any swaying or side-to-side play.
- Misalignment – Worn bearings lead to misaligned pulleys, which produce belt chirp noise issues.
- Pulley that is cracked or broken: Look for visible physical damage.
- Free Spin Pulley: Use your fingers to spin the pulley. Does it rotate more than a couple of times? If it happens, the lack of lubricant in the bearing is the cause and a warning that it may soon fail.
- Bearings that are seized are a sign that the pulley will lock up.
- Discoloration – This may be brought on by the pulley bearing intermittently seizing up or by a faulty tensioner causing the belt to slip.
- The surface buildup is a telltale sign of a belt that is slipping due to a worn-out tensioner.
Maintenance and Replacement of a Tensioner Pulley
The tensioner pulley wears out over time due to its free-spinning activity. It is essential to inspect the pulleys and bearings during maintenance for best practice. It is becoming more common to complete the primary transmission maintenance, replacing all components of the distribution subject to wear at once.
Technicians recommend replacing the water pump in this operation for three reasons: greater quality and safety of service, best fit together of all components from the start, and greater savings.
To ensure the longevity and efficiency of your vehicle’s engine, proper maintenance of its various components, including the tensioner pulley, is essential. Regular inspections should be performed at least once a year or as recommended by the manufacturer, looking for signs of wear, damage, or looseness. Lubrication should be followed as recommended to prevent premature wear.
The area around the tensioner pulley should be clean and free of debris to prevent damage over time. If any signs of wear, damage, or looseness are noticed, the tensioner pulley should be replaced. The accessory belt and tensioner should be replaced simultaneously to prevent premature wear.
You should learn about Belt and Pulley with this detailed guide!
FAQs
What happens when a tension pulley goes bad?
The drive belt can experience unusual and fast wear if the tensioner pulley has any kind of problem. The margins of the belt may tear from a poor pulley, and in extreme circumstances, it may even shatter.
How do I know when to replace my tensioner pulley?
Examine to check if the pulley spins freely. Replace the tensioner if you hear grinding or if the pulley doesn’t spin freely. Moving the tensioner should need a lot of force when you change the belt. If it is simple to move, the spring tension is probably insufficient.
Can the tensioner cause a loss of power?
All of the parts that depend on the belt for power will stop working if the tensioner wears down and causes the belt to totally dislodge, probably through seizing. This implies that if the belt comes loose, your car’s power steering, water pump, alternator, and smog equipment will all stop working.
What causes the tensioner to make noise?
The belt squeaks because the belt drive system’s tension isn’t correct. In addition to a polluted belt (oil, belt dressing, etc.) and a worn-out automatic tensioner, additional potential causes include excessively lengthy or worn-out belts.
What is the lifespan of a tensioner pulley?
The serpentine belt, tensioners, and idler pulleys on the majority of newer cars will last 60,000 to 100,000 miles after they leave the dealer’s lot.
When should I replace my car tensioner?
Drive belt lifespans typically range from 40,000 to 70,000 miles. There is really only one warning indication that a drive belt tensioner has reached the end of its useful life.